Independent tool advice for DIY and home repair. As an Amazon Associate I earn from qualifying purchases.
Roundup

Best Screw Extractor Sets for Small Stripped Screws

By PauliusUpdated

Small screws strip faster than big ones. The head is shallow, the recess is tiny, and once a bit spins out a couple of times there is almost nothing left to grip. A cabinet hinge screw, a #6 screw in a light switch plate or an M2 screw in a laptop can stop a whole job.

A screw extractor fixes that. You drill a small hole in the screw, and a hardened bit with a reverse thread bites into the hole and turns the screw out. The catch is size. Most extractor sets are built for bolts, and their smallest piece is still too big for the screws this article is about. So I picked these eight for one job: getting small stripped screws out, from about M1.2 up to 1/4 inch.

I chose them from their Amazon listings and the makers’ size charts, and from what buyers consistently report. I have not tested all eight side by side, and I say so plainly. What I can add after 15 years of working with tools is which type suits which screw, which size to reach for and how to avoid the classic mistake of snapping an extractor off inside the screw.

Best screw extractors for small screws: quick comparison

Pick Best for Type Smallest size (stated) Drilling needed
Alden 4507P Grabit Micro Best overall for small screws 2-in-1 drill and extractor bits #5 screws, 3 mm Yes, in reverse
VAMPLIERS 5″ Mini pliers Best for laptops and electronics Extraction pliers M1.2 screws No
VAMPLIERS 6.25″ pliers Best when the head sticks up Extraction pliers Heads from 3 mm No
Nuovoware 22-piece Most sizes for the money Double-ended drill and extractor bits 1.3 mm extractor, 1.5 mm drill Yes
IRWIN 53535 5-piece Best name-brand budget pick Spiral extractors EX-1, for 3/32 to 5/32 in. Yes, bits sold separately
WYBENZ 14-piece Best kit with left-hand bits Spiral extractors plus left-hand bits #1 extractor, 1/8 in. bit Yes
DOAHO 9-piece Cheapest that works Double-ended bits plus twist bits #0 extractor, 2.0 mm bit Yes
coobeast 35-piece If you also get stuck bolts Spiral and multi-spline plus left-hand bits Not stated on listing Yes

Specs are taken from each Amazon listing and the maker’s size chart (retrieved 2026-11-19).

Before you drill anything: an extractor is the last resort, not the first. A better-fitting bit, a rubber band or a few taps with a hammer often do the job without damage. I go through all nine methods in order in my guide on how to remove a stripped screw.

Screw Extractor Sets

Which extractor for which screw

Your screw What works What struggles
Tiny electronics screws, about M1.2 to M2 (laptops, phones, consoles) Mini extraction pliers if the head is raised. The smallest double-ended bits, used by hand or at very low speed. Standard extractor sets. Even their smallest piece is too big.
Small screws, #4 to #8 or M2.5 to M4 (hinges, switch plates, toys, small appliances) Alden Grabit Micro, IRWIN EX-1, the small sizes in double-ended kits Bolt extractor kits that start at 1/8 in. bits
Medium screws, #10 to 1/4 in. or M5 to M6 (deck screws, machine screws) Almost any set here, including the larger kits Mini pliers. Their jaws are too small.
Head sticks up above the surface Extraction pliers. No drilling at all. Nothing. This is the easy case.
Head is flush or countersunk A drill-in extractor Pliers, which need an edge to bite

The 8 best screw extractor sets for small stripped screws

1. Alden 4507P Grabit Micro – best overall for small screws

Alden 4507P Grabit Micro Broken Bolt Extractor 4 Piece Kit - Small Bolt and Screw Remover - Made in the USA

This is the set competitors keep naming for small fasteners, and the reason is the design. Each of the four bits has a drill on one end and an extractor on the other. The drill end has a self-centering tip, so it does not walk across the screw head, and you do not need to center punch first. You drill in reverse, flip the bit and back the screw out.

Alden 4507P Grabit Micro Broken Bolt Extractor 4 Piece Kit - Small Bolt and Screw Remover - Made in the USA

Alden’s size chart covers four sizes: #5, #6 and 3 mm, then #8 and 4 mm, #10 and 5 mm, and 1/4 in. and 6 mm. The bits are M2 high speed steel, tempered twice and made in the USA. Alden recommends a variable speed reversible drill at slow speed. The shanks are thin, so a big drill chuck that does not close down well can slip on the smallest one. On Amazon it holds 4.2 stars from over 1,000 ratings.

  • Good: self-centering tip, so the drill does not wander on a small head
  • Good: one tool does both jobs, so there is no swapping bits
  • Good: covers the common small screw sizes from #5 to 1/4 in.
  • Not so good: the most expensive per piece of anything here
  • Not so good: the smallest bit starts at #5 and 3 mm, too big for most laptop screws
  • Not so good: small shanks need a chuck that grips well

Buy it if: you want the most dependable way to remove small stripped screws from hinges, appliances, firearms, bikes and RC gear.

Check the current price of the Alden Grabit Micro on Amazon

2. VAMPLIERS 5″ Mini – best for laptops and electronics

VAMPLIERS 5' Mini Stripped M2 Screw Extractor Pliers ESD Safe TPR Handles | Made in Japan, Remove Screws Ø2 - 3.5mm, High Carbon Steel, For Removing Small Specialty Fasteners in Electronic Devices

The screws inside a laptop or phone are often smaller than any drill-in extractor. For those, pliers are the better tool. Vampliers have jaws with vertical serrations that bite into the side of a screw head, so you can grip it and turn it out without drilling.

VAMPLIERS 5' Mini Stripped M2 Screw Extractor Pliers ESD Safe TPR Handles | Made in Japan, Remove Screws Ø2 - 3.5mm, High Carbon Steel, For Removing Small Specialty Fasteners in Electronic Devices

This mini version is made for small electronics screws. The listing says it handles M1.2 to M2 screws, with heads from 2 to 3.5 mm, in laptops, circuit boards, phones and game consoles. It is 5 inches long, the jaws are high carbon Japanese steel, and the handles are rated ESD safe. It holds 4.8 stars from more than 1,200 ratings.

  • Good: no drilling, so no metal chips inside the device
  • Good: sized for laptop and phone screws, where extractor bits are too big
  • Good: ESD-safe handles for work near circuit boards
  • Not so good: needs a head that sits above the surface, so it cannot reach flush or recessed screws
  • Not so good: too small for ordinary household screws

Buy it if: you repair laptops, consoles, phones or other small electronics.

Check the current price of the VAMPLIERS Mini on Amazon

3. VAMPLIERS 6.25″ – best when the head sticks up

VAMPLIERS 6.25' Stripped Screw Extractor Combination Pliers | Made in Japan, High Carbon Steel, TPR Handles, Remove Damaged/Rusted Fasteners Ø3 - 9.5mm, Side Wire Cutter, Spring-Loaded

This is the full-size version, and it is the pick Bob Vila and many tradespeople name when someone asks about extraction pliers. If the screw head is raised even a little above the surface, these grab it from the side. You do not need to drill, so there is no risk of snapping a hardened bit inside the screw.

VAMPLIERS 6.25' Stripped Screw Extractor Combination Pliers | Made in Japan, High Carbon Steel, TPR Handles, Remove Damaged/Rusted Fasteners Ø3 - 9.5mm, Side Wire Cutter, Spring-Loaded

The listing gives a range of screw heads from 3 to 9.5 mm. It is 6.25 inches long, with high carbon Japanese steel jaws and a wire cutter built in. It has the largest review base in this list, with 4.7 stars from more than 3,100 ratings, and a 4-year warranty.

  • Good: the fastest fix when the head is raised
  • Good: no drilling, no extra damage
  • Good: also works on rusted and odd-shaped heads
  • Not so good: useless on flush, countersunk or recessed screws
  • Not so good: costs more than a basic extractor kit

Buy it if: you often deal with raised screw heads on cabinets, outlets, machinery or cars, and want a tool that skips drilling.

Check the current price of the VAMPLIERS 6.25″ on Amazon

4. Nuovoware 22-piece – most sizes for the money

Nuovoware Damaged Screw Extractor Set, 22 PCS Stripped Screw Extractor Kit | All-purpose HSS Broken Screw Remover Set with Magnetic Extension Bit Holder & Socket Adapter, Black

This kit has double-ended bits: a cutting end to drill into the screw and an extractor end to pull it out. What makes it useful for small screws is how small it goes. The listing gives drill sizes from 1.5 mm and extractor sizes from 1.3 mm, which is smaller than most kits.

Nuovoware Damaged Screw Extractor Set, 22 PCS Stripped Screw Extractor Kit | All-purpose HSS Broken Screw Remover Set with Magnetic Extension Bit Holder & Socket Adapter, Black

There are 10 sizes in total, up to a 5.9 mm drill and a 5.7 mm extractor. The kit also includes a magnetic extension and a socket adapter, so you can reach into recessed holes. The bits are 4341 high speed steel, which is fine for ordinary screws and not meant for hardened ones. Its rating is the lowest here at 3.8 stars, across more than 4,600 ratings, so expect some bits to wear quickly.

  • Good: very small sizes, down to a 1.3 mm extractor
  • Good: lots of sizes, plus an extension for deep holes
  • Good: low price for what is in the box
  • Not so good: lowest rating in this list
  • Not so good: softer steel than the Alden or the left-hand drill bit kits

Buy it if: you want one cheap kit that covers screws from tiny to medium and you do not need it every week.

Check the current price of the Nuovoware kit on Amazon

5. IRWIN 53535 5-piece – best name-brand budget pick

IRWIN Screw Extractor for Spiral Screws, 5-Piece (53535)

This is the classic Hanson spiral extractor set: five extractors, EX-1 to EX-5, in a pouch. Each one has its size and the matching drill bit size etched on it. The spiral flutes bite deeper as you turn, so the grip gets stronger as the screw resists.

IRWIN Screw Extractor for Spiral Screws, 5-Piece (53535)

For small screws, EX-1 is the one that matters. IRWIN rates it for fasteners from 3/32 to 5/32 inch (2.4 to 4 mm) with a 5/64 inch pilot hole. The set covers up to 5/8 inch overall. There are no drill bits in the box, so you need your own. It has 4.2 stars from more than 4,000 ratings.

  • Good: trusted brand at a budget price
  • Good: size and drill bit etched on every piece, so no guessing
  • Good: EX-1 suits common small screws
  • Not so good: no drill bits included
  • Not so good: only one size really suits small screws

Buy it if: you already own good drill bits and want a proven extractor set that lasts.

Check the current price of the IRWIN 53535 on Amazon

6. WYBENZ 14-piece – best kit with left-hand bits

14Pcs Screw Extractor Set and Left Hand Drill Bits Set Easy Out Extractor | Broken Bolt Extractor Kit, Stripped Screw Extractor Kit for Remove Broken Bolt & Screw,35# Cr-Mo & 6542 HSS Steel Cobalt

Left-hand drill bits cut while turning counterclockwise, the same direction that loosens a screw. Often the bit grabs and spins the screw out before you even need the extractor. This kit pairs seven left-hand HSS bits with seven spiral extractors.

14Pcs Screw Extractor Set and Left Hand Drill Bits Set Easy Out Extractor | Broken Bolt Extractor Kit, Stripped Screw Extractor Kit for Remove Broken Bolt & Screw,35# Cr-Mo & 6542 HSS Steel Cobalt

The extractors are #1, #1, #2, #2, #3, #4 and #5, and the bits run from 1/8 to 19/64 inch, with doubles of the small sizes you will wear out first. The listing gives the bits a hardness of HRC 63 to 66 and says not to use them on 440 stainless. The smallest bit is 1/8 inch, so on screws under about #8 you will need a smaller bit of your own. It has 4.2 stars from almost 1,700 ratings.

  • Good: left-hand bits can back the screw out on their own
  • Good: spare #1 and #2 extractors for the sizes that break most
  • Good: case keeps everything sorted
  • Not so good: the smallest bit is 1/8 in., big for tiny screws
  • Not so good: not for hardened stainless screws

Buy it if: you deal with #8 to 1/4 in. screws and want the left-hand drill advantage at a low price.

Check the current price of the WYBENZ kit on Amazon

7. DOAHO 9-piece – cheapest that works

DOAHO 9 PCS Damaged Screw Extractor Set,Birthday Gifts for Adult Men | 6 HSS 4341 Screw Extractor Remover Kit and 3 Twist Drill Bit Kit for Stripped Screws & Drill Bit Tools

For about the price of a sandwich you get six double-ended extractors and three twist bits. The sizes are small: extractors #0, #1, #2, #2, #3 and #4, and drill bits of 2.0, 3.0 and 3.5 mm. That makes it a better match for small screws than many bigger kits.

DOAHO 9 PCS Damaged Screw Extractor Set,Birthday Gifts for Adult Men | 6 HSS 4341 Screw Extractor Remover Kit and 3 Twist Drill Bit Kit for Stripped Screws & Drill Bit Tools

The maker is honest about the limits. The listing says the 4341 high speed steel is for plastic, wood, aluminum, copper, iron and thin stainless, and not for thick stainless, high carbon or alloy steel. For soft hardware store screws in furniture, toys and fixtures, that is enough. It has 4.0 stars from over 900 ratings.

  • Good: very low price
  • Good: small sizes, down to #0 and a 2 mm bit
  • Good: spare #2, the size you will use most
  • Not so good: softer steel, not for hardened screws
  • Not so good: basic case and no extension

Buy it if: you have one or two stripped screws to deal with and want a cheap kit for the drawer.

Check the current price of the DOAHO kit on Amazon

8. coobeast 35-piece – if you also get stuck bolts

35 Pcs Screw Extractor Set,Left Hand Drill Bits Set Screw Extractor Kit | High-Hardness,Wear Resistance,Easy Out Screw, Stocking Stuffers for Men,with Portable Case,Gifts for Adults Him,Home DIY

This is the big kit. It has 16 left-hand cobalt drill bits with titanium coating, 13 multi-spline extractors that fit a socket or wrench and 6 spiral extractors. It is here for one reason: if your small screw problem sits next to rusted bolts on a car, trailer or mower, one case covers both.

35 Pcs Screw Extractor Set,Left Hand Drill Bits Set Screw Extractor Kit | High-Hardness,Wear Resistance,Easy Out Screw, Stocking Stuffers for Men,with Portable Case,Gifts for Adults Him,Home DIY

The extractors are chromium-molybdenum steel, and the case is blow-molded. The listing does not state the smallest size in mm or screw gauge, and most of the kit is aimed at bolts. The listing also says the drill bits are not for stainless steel. It has 4.4 stars from almost 1,600 ratings.

  • Good: covers small screws and large bolts in one case
  • Good: multi-spline extractors can be turned with a ratchet for more force
  • Good: left-hand cobalt bits
  • Not so good: overkill if you only deal with small screws
  • Not so good: the most expensive pick here

Buy it if: you work on cars, bikes or equipment and want one extractor kit for everything.

Check the current price of the coobeast kit on Amazon

How to choose an extractor for small screws

Match the extractor to the screw, not the other way round

The pilot hole has to be smaller than the screw’s core, or you drill through the walls and leave nothing to grip. Start with the smallest extractor that fits the screw and go up one size only if it will not bite. Reviewers of the Alden set say the same: when one size slips, the next size up often works.

Screw size Approx. metric Extractor that fits (from maker charts)
#0 to #2 M1.2 to M2 VAMPLIERS Mini, smallest double-ended bits (Nuovoware 1.3 mm, DOAHO #0)
#4 to #6 M2.5 to M3.5 IRWIN EX-1, Alden #5-#6 bit, small double-ended bits
#8 M4 Alden #8 bit, IRWIN EX-1 or EX-2, WYBENZ #1
#10 to 1/4 in. M5 to M6 Alden #10 and 1/4 in. bits, IRWIN EX-2, any kit here

Drill-in extractor or pliers

If any part of the head stands above the surface, try pliers first. No drilling means no chance of a broken bit and no metal chips. If the head is flush or sunk into a hole, you need a drill-in extractor.

Spiral, straight or 2-in-1

Spiral extractors grip harder the more the screw resists. Straight flute extractors do not expand the screw, which matters in thin or brittle material such as a plastic boss inside a device. 2-in-1 bits like the Alden drill and extract with the same tool, so the extractor always matches the hole.

Steel matters more on small sizes

A small extractor is thin, and thin hardened steel snaps easily. M2 high speed steel, like the Alden bits, and cobalt bits hold up better on hard screws. Kits in 4341 HSS are fine for ordinary soft screws, and their makers say so.

Left-hand drill bits are worth having

A left-hand bit drills while turning counterclockwise. The heat and grab of drilling often loosen the screw, and it comes out on the bit. Then you never need the extractor at all.

How to use an extractor on a small screw, step by step

  1. Clean out the head and, if the screw is rusted, add a drop of penetrating oil and wait 15 minutes.
  2. Mark the exact center. A self-centering bit like the Alden does not need it. For everything else, make a small dent with a center punch or a sharp nail.
  3. Set the drill to reverse and to its lowest speed. High speed burns small bits and makes them wander.
  4. Drill a pilot hole straight down, using the size the maker gives for that extractor. Keep the drill square to the screw.
  5. Fit the extractor and turn it counterclockwise with steady pressure, by drill at low speed or by hand with a tap wrench.
  6. If it stops turning and you feel the extractor twisting, stop. Do not force it. Add oil, tap the extractor lightly and try again.

If you are not sure whether to use a drill or an impact driver for this, a drill with a clutch gives far better control. I explain the difference in impact driver vs drill.

If the extractor breaks off

This is the mistake to avoid. Extractors are harder than normal drill bits, so a broken one cannot simply be drilled out. It usually takes a carbide bit or a trip to a machine shop. Small extractors break from too much force, too much speed or a crooked hole, which is why the steps above say slow and straight.

Tiny screws in electronics

  • Try pliers first. Drilling throws metal chips onto circuit boards.
  • Watch the plastic. Many laptop screws sit in thin plastic posts. A wedge-type extractor can crack them, so turn gently.
  • Work by hand. On screws under M2, a small extractor turned in a pin vise gives more control than a drill.
  • Check the screw type. Older Japanese electronics often use JIS screws. They look like Phillips, but a Phillips bit strips them. A JIS bit may save you the extraction.
  • Disconnect the battery before you work near the board.

Frequently asked questions

Can a screw extractor remove very small screws?

Yes, if the set goes small enough. Many kits start at sizes meant for bolts. For #4 to #8 screws, look for sizes like IRWIN EX-1 or the Alden #5-#6 bit. For laptop screws around M2, extraction pliers or the smallest double-ended bits work better.

What size extractor do I need for a #6 screw?

A #6 screw is about 3.5 mm across. The Alden #5-#6 bit and the IRWIN EX-1, which is rated for 3/32 to 5/32 in., both fit it. Always use the pilot drill size the maker gives for that extractor.

Spiral or straight flute: which is better?

Spiral grips harder and suits most stuck screws. Straight flute does not expand the screw, which is safer in thin or brittle material. For small screws in metal, spiral or a 2-in-1 bit is the usual choice.

Do I need left-hand drill bits?

They are not required, but they help. A left-hand bit drills in the loosening direction, so it often removes the screw before you need the extractor.

Can I use a screw extractor with an impact driver?

Not with small extractors. The hammering can snap a thin hardened bit. Use a drill at low speed in reverse, or turn the extractor by hand. Some heavy multi-spline extractors are made for impact use, but they are for bolts, not small screws.

What do I do if the extractor breaks in the screw?

Stop drilling. Normal bits will not cut it. A carbide bit, a small rotary tool or a machine shop is the usual fix. In wood, it is often easier to cut around the screw with a plug cutter and fill the hole.

Will Vampliers work on laptop screws?

The 5 inch Mini is made for them, with a stated range of M1.2 to M2 screws. It needs some of the head above the surface to grip.

The bottom line

For most small stripped screws in metal, the Alden 4507P Grabit Micro is the one I would buy. It centers itself and does both jobs with one bit. For laptops and electronics, get the VAMPLIERS 5″ Mini, and for raised heads around the house, the VAMPLIERS 6.25″. On a tight budget, the DOAHO 9-piece or the Nuovoware 22-piece will handle soft screws. And before you drill, try the easier fixes in my guide on how to remove a stripped screw.